Motion Casts
Windows 10 & 11 Buy license · $69.95
Editing

How to Remove Um and Uh From a Video (Filler Words) Without Re-Recording

Remove um and uh from a video without re-recording. Manual and automatic ways to cut filler words from a voiceover, and how to keep cuts sounding smooth.

Updated 5 minute read The Motion Casts team

To remove "um" and "uh" from a video, you find each filler word, cut it out, and close the gap so the sentence flows on. You can do this by hand in any timeline editor by listening and splitting the clip around each one, or you can use a tool that transcribes your speech, spots the filler words automatically and lists every cut for you to approve. Either way, a small amount of padding around each cut and a final listen-through are what keep the result sounding natural.

This guide covers both methods, which filler words are safe to cut, how to avoid robotic-sounding edits, and how to say fewer of them in the first place.

Why filler words are worth cutting

Everyone says "um" and "uh". In a live conversation, nobody notices. In a recorded video, they stand out, for a few reasons:

  • They slow the pace. A tutorial with a filler word every sentence feels longer than it is.
  • They undermine confidence. Viewers read hesitation as uncertainty, even when you know the subject well.
  • They clutter captions. Automatic captions either transcribe them, which looks messy, or skip them, which leaves captions slightly out of step with the audio.

The goal is not perfect, scripted delivery. It is removing the hesitations that get in the way of the message.

Method 1: Remove filler words by hand

Any timeline editor can do this. It is slow but gives you full control.

  1. Import your recording and zoom into the audio waveform.
  2. Play the video and stop when you hear a filler word. Filler words usually appear as a short, rounded blob on the waveform, often right after a pause.
  3. Split the clip just before the "um" starts and just after it ends.
  4. Delete the piece and close the gap.
  5. Play back a few seconds either side to check the join sounds natural.
  6. Repeat through the whole video.

For a two-minute clip, this is manageable. For a twenty-minute tutorial, you might be looking at a hundred or more cuts, and it becomes the slowest part of the edit.

Use the keyboard. Most editors have shortcuts for split, ripple delete and play around the playhead. Learning those three makes manual editing several times faster.

Method 2: Remove filler words automatically

Automatic tools use speech recognition to transcribe your audio, then flag words like "um" and "uh" with their exact timings. Instead of hunting through the waveform, you review a list.

In Motion Casts, filler-word removal works alongside silence removal:

  1. Open your recording in the editor.
  2. Run silence removal. Motion Casts finds long pauses and filler words such as "um" and "uh" across the whole recording.
  3. Review the list of proposed cuts. Each one can be approved or skipped.
  4. Apply the cuts. The timeline closes up around them.
  5. Play the video through once to check the flow.

Because pauses and filler words usually come together ("So... um... the next step"), handling both in one pass gives a much cleaner result than doing them separately. Our guide to removing silence from a video automatically explains the pause settings in detail.

Which filler words to cut, and which to keep

FillerSafe to cut automatically?Notes
Um, uh, er, ermUsually yesThey carry no meaning, so removing them rarely changes a sentence
Like, you know, I meanNo, check by handThese are also real words; "click Like" must stay
So, right, okay at the start of a sentenceCase by caseSometimes filler, sometimes a useful transition
Repeated words ("the the")By handCut the first one and keep the second
False startsBy handCut back to the start of the clean take

Do not aim for zero. Removing every single hesitation can make speech sound strangely relentless. A good rule is to cut fillers that interrupt an instruction, and leave the odd one that sits naturally between thoughts.

How to keep cuts sounding natural

  • Cut at the quietest point. Split in the brief silence before and after the filler word, not in the middle of a sound.
  • Leave a tiny gap. Keep a tenth of a second or so of natural pause where the "um" was. Words that slam together sound edited.
  • Watch your breaths. Cutting a breath along with an "um" can make the next sentence feel rushed. Sometimes it is better to keep the breath and lose only the filler.
  • Check the webcam. If your face is on screen, each cut creates a small jump. A small webcam overlay hides this far better than a full-screen camera shot.
  • Listen at normal speed. Problems that are obvious at normal speed can be invisible when you scrub through quickly.

Cut fillers before you add captions

Order matters. If you generate captions first and then remove filler words, every caption after the first cut can drift out of sync. Do your cleanup first, then generate captions on the finished edit, then proofread them. Our guide to adding captions to a video automatically walks through that last step.

How to say um less in the first place

Editing out filler words is easier when there are fewer to find. Filler words usually appear when your brain is searching for the next thing to say. These habits help:

  • Use notes or a script. Knowing what comes next removes most of the hesitation. A teleprompter beside your webcam lets you read without looking away; see our guide to using a teleprompter on your PC.
  • Pause silently instead. When you need a moment, close your mouth and pause. A silent pause is easy to cut; a filled one is harder.
  • Slow down. Rushing makes your speech get ahead of your thoughts.
  • Record in sections. Pause the recording between steps, plan the next one, then resume.
  • Rehearse once. A single run-through out loud catches the sentences you stumble over.

What about live recordings and meetings?

The same techniques work on recorded webinars, interviews and meetings, with one caution: when several people are speaking, make sure a cut does not clip the start of someone else's sentence. Review cuts more carefully where voices overlap, and keep the conversation's natural back-and-forth rather than tightening every gap.

Quick reference

  1. Record with notes, pausing silently instead of filling gaps.
  2. Remove long pauses and "um" and "uh" in one pass.
  3. Review each cut, keeping natural pauses and breaths.
  4. Fix repeated words and false starts by hand.
  5. Generate captions on the final edit, then proofread.

Frequently asked questions

How do I find filler words in a long video?

Manually, you scrub the waveform and listen for them. Automatic tools use the transcript to find each um and uh and list them so you can approve each cut.

Should I remove every filler word?

Not always. Removing nearly all of them tightens a tutorial, but an occasional one can keep speech sounding natural. Review each cut rather than deleting blindly.

How can I say um less when recording?

Use a script or bullet notes, pause silently instead of filling the gap, and slow down. A teleprompter next to your webcam helps you keep your place.

Get three guides like this every month, plus software update notices.Subscribe →